Relationship

IPMP CONFIGURATION IN SOLARIS 10 PDF

These topics include IPv4 and IPv6 network configuration, managing TCP/IP 1. Oracle Solaris TCP/IP Protocol Suite (Overview) The default is 10 seconds. Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the.

Author: Grotaxe Makazahn
Country: Cyprus
Language: English (Spanish)
Genre: Technology
Published (Last): 7 February 2007
Pages: 202
PDF File Size: 18.24 Mb
ePub File Size: 18.11 Mb
ISBN: 216-7-50597-496-1
Downloads: 44835
Price: Free* [*Free Regsitration Required]
Uploader: Gohn

No test address configured on interface hme0; disabling probe-based failure detection on it. An active interface is a physical interface that transmits both data traffic and probe traffic.

Do not use DHCP on data addresses. Specific information about DR in the Sun Fire environment. For more information about target system use in probe-based failure detection, refer to Probe-Based Failure Detection. This process is called load spreading. Network access includes IPv4 unicast, multicast, and broadcast traffic, as well as IPv6 unicast and multicast traffic.

Data Addresses Data addresses are the conventional IPv4 and IPv6 addresses that are assigned to an interface of a NIC at boot time or manually, through the ifconfig command. Then, the NIC is unplumbed from the system. Opmp a system has multiple interfaces attached to the same link, you can configure IPMP to perform failover if one of the interfaces fails.

Failure Detection and Failover Failure detection is the process of detecting when an interface or the path from an cconfiguration to an Internet layer device no longer works. Due to these restrictions, you must use the ifconfig command to mark any test addresses as deprecated and -failover prior to setting the interface as standby. Solaris 11 IPMP provides two different methods for probe-based failure detection, the default method by using test addresses, and the transitive probing method without additional test addresses.

  ISO 1873-2 PDF

How to configure Solaris 10 Link Based IPMP

Solaris11 Self Paced Video Learning. For example, you would create the following test address for the primary network interface hme IPMP does not permit you to add a data address to an interface that is configured through the ifconfig command as standby.

Free Courses We Offer. You can observe this 110 in the status lines for the interface in the ifconfig output. During IPMP group configuration, in. Due to these restrictions, you must use the ifconfig command to mark any test addresses as deprecated and -failover prior to setting the interface as standby.

How to configure Solaris 10 Probe based IPMP

If no routers exist on the link, in. Thus, the final network configuration is identical to the configuration that would have been made if the system had been booted with the interface present. IPMP provides increased reliability, availability, and network performance for systems with multiple physical interfaces.

The attachment of the interface to the IP link is down. You should configure only test addresses on a standby interface. The alternate interface s that cannot receive inbound packets here: IP network multipathing IPMP provides physical interface failure detection and transparent network access failover for a system with multiple interfaces on the same IP link. Currently you have JavaScript disabled.

For a repair detection time of 10 seconds, the probing rate is approximately one probe every two seconds.

How to configure Solaris 10 IPMP ? – UnixArena

The failover feature of IPMP preserves connectivity and prevents disruption of any existing connections. Internet Key Confuguration Overview Network Interface Card A network interface card is a network adapter that can be built in to the system.

  BCIS SMM7 ESTIMATING PRICE BOOK PDF

These interfaces and the data addresses that are configured on them are immediately 100 for use by the IPMP group. Some NICs can have multiple physical interfaces. Administering Mobile IP Tasks However, IPMP does impose the following requirements on your network configuration and topology: Test addresses are IPMP-specific addresses that are used by the in.

Solaris 11 Administration Information Center unixadminschool. Your email address will not be published.

Modifying IPMP Configurations – System Administration Guide: IP Services

The interface can still be used for probe traffic. You can check the status of an interface by issuing the ifconfig interface command.

Configuring IKE Tasks The dummy address is removed when a subsequent failback takes place. You need to configure a test address only if you want to use probe-based failure detection on a particular interface. Solaris 11 Administration Live WebEx. Internet Key Exchange Reference Detecting Physical Interface Repairs For the in. IPMP requires the manual fixed network configuration mode resp.

Administering Network Interfaces Tasks 7. Configuring IPsec Tasks Configuring IPsec Tasks Similarly, if you configure as standby an interface that already has data addresses, these addresses automatically fail over to another interface in the IPMP group. The test IP addresses must belong to a single IP subnet. You can remove the component from the system. Configuring an IPv6 Network Tasks. More Posts from this Category. An IPMP configuration typically consists of two or more physical interfaces on the same system that are attached to the same IP link.