Life

FBI XL2T PROGRAM PDF

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Dougrel Yozshuzshura
Country: Mozambique
Language: English (Spanish)
Genre: Music
Published (Last): 5 February 2016
Pages: 345
PDF File Size: 6.42 Mb
ePub File Size: 20.31 Mb
ISBN: 674-2-88599-200-9
Downloads: 58719
Price: Free* [*Free Regsitration Required]
Uploader: Arashiktilar

Comments to this Manuals Your Name. If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode.

FBII XL-2T Installation And Setup Manual

The checkmark highlights which options are selected. Refer to the Installation Instructions for hookup information. The system must be in ready fvi. Next, enter the desired account number each digit followed by the key. Don’t show me this message again. Question 32, L1 – Bypass Code If a keypad tamper code is entered then it will be transmitted to the Central Station.

The alarm was then activated, without me activating it. If the siren is already sounding, the supervision will not take effect until after bell cutoff time. For a period of vbi seconds the fire zone will not be scanned allowing the smoke detectors to settle.

Directly to a single or double gang electrical junction box. Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: I want to change this 3 digit code to a new 4 digit code, but with no success.

  5F6A SCHEMATIC PDF

FBII XL-2T INSTALLATION AND SETUP MANUAL Pdf Download.

The keypads are surface mounted as described below. Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting.

A-2 Partial Extended 3×1 Part.

The auto arm time represents the time of day that the area will automatically arm if it is not already armed. Page 40 Section 5 – System Operations If a user code is not required to set the time, then enter: Enter text from picture: The system will report all signals to the cbi receiver phone number. I shall be pleased to learn from you in this regard.

Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3. This equipment generates and uses radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to radio and television reception.

I pressed the code button ready light did not flashthen pressed both 7 and 9 at same time, to reset master code to LCD display keypads will indicate the following message: When the switch is pushed toward the front of the keypad, in the opposite direction of the arrowthe switch is in the OFF position. How can i change or get rid of this 3 digit code. Proceed to question 02 through the sequence Page 81 – Extended 3×1 Ext. Page 70 Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: Trigger 1 must be selected for smoke detector power reset for this feature to active.

  EMPATI ADAM FAWER PDF

By pressing ‘print’ button you will print only current page.

Question 10, L1 – Burglary Bell Time-out Question 11, L1 – Exit Delay The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected. Fbl 5 – System Operations Keypad Sounder The sounder or pdogram housed inside the keypad, emits annunciates sounds according to the condition of the security system. The keypads can be surface mounted or flush mounted as described below. Secure keypad to double-gang box as shown in graphic at left.

The system features seven 7 fully programmable zones. It is time to change code for security reasons.

Select the desired location between wall studs for mounting the keypad. Got it, continue to print. Create an rpogram and mount a standard double-gang box.

Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected x2lt ZONE modules will be reset for a period of 8 seconds. Don’t have an account? Replacement microprocessors are available through Technical Support or Customer Service.

Keypad Sounder Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system. Section 5 – System Operations If rpogram user code is not required to set the time, then enter: