Environment

ELIWELL ID970 PDF

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Yozshurisar JoJojas
Country: Tanzania
Language: English (Spanish)
Genre: History
Published (Last): 22 September 2010
Pages: 388
PDF File Size: 5.59 Mb
ePub File Size: 15.66 Mb
ISBN: 527-7-38943-575-9
Downloads: 91041
Price: Free* [*Free Regsitration Required]
Uploader: Malat

Compressor off time in the event of a faulty probe. Defrost cycles can be controlled at time intervals. Maximum possible setpoint value.

They are provided with a PTC thermostatic probe input NTC can be selected by parameter and two relay outputs for compressor and defrost management. It is classified as follows: The operation cannot be cancelled.

Make sure that the power voltage complies with the device voltage. For this page to function properly, you must enable JavaScript. Users must not be able to access parts with dangerous voltage levels under normal operating conditions. The relay contacts are voltage-free. The same applies to any person or company involved in preparing and writing this document. Delay after switching off. For higher loads, use a suitable contactor. Alarm exclusion time after instrument is switched on following a power failure.

ID A Single stage controller for temperature. The password is enabled if the value of the PA1 parameter is not 0. Between the request and effective activation of the compressor relay, at least the specified time must elapse. Temperature alarm signal delay time.

  MAINLINE MODELER PDF

Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in a downward direction triggers the activation of the alarm signal.

The two sets are interdependent: Do not assemble the instrument in excessively humid or dirty locations since it is designed to be used in locations with normal pollution levels. Although Eliwell has taken all possible measures to guarantee the accuracy of this document, it declines any responsibility for any damage arising out of its use. Eliwell reserves the right to make any changes or improvements without prior notice and at any time.

Always make sure that the area next to the cooling openings of the tool is adequately ventilated. Drill a 29×71 mm hole, insert a tool and fix it in place with the brackets provided.

It should be noted that the relay contacts supplied with the device are functional and therefore exposed to potential faults. All the versions are provided with a TTL connection in order to use Copy Card, the quick programming accessory.

The parameter indicates that a protection is active on the relay actuations of the generic compressor. Minimum possible setpoint value. It’s a community-based project which helps to repair anything. This means, for example, that an error eliqell by the probe is added to any error that is typical eliwfll the instrument. Probe cables, power supply cables and the TTL serial cable should be kept separate from power cables.

  CHATUVULU TELUGU PDF

Do not exceed the maximum current allowed. Fliwell least the indicated time must elapse between switch-off of the compressor relay and the successive switch-on.

Eliwell ID MC (Milk) |

If elieell do not enable JavaScript, certain features in this page will not function correctly. The ID controllers are devices suitable for applications on normal or low temperature refrigerating units. Elwell are 2 operating modes determined by parameter AtP: Programming parameter transfer from Copy Card to instrument. Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in an upward direction triggers the activation of the alarm signal.

Eliwell ID970 MC (Milk)

Delay time in activating the outputs after switch-on of the instrument or after a power failure. In normal conditions, the labels for the Set point value is found in the menu. Positive or negative temperature value added to the value read by probe Viewing mode during defrosting.

The continuous improvement of our products can cause some variations in this non contractual document even without notice. Set point setting folder; -Pb1: The Setpoint can also be viewed.

Programming parameter transfer from instrument to Copy Card. The Setpoint value appears on the display.