AHM E8/E8M – 13a. G–Gauge length. Dimensions, mm [in.] For Test Specimens with Gauge Length Four times the Diameter (E8]. Standard. Small-Size. Buy ASTM E 8/E8M: A TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS from SAI Global. Originally contact ASTM Customer Service at [email protected] For Annual Book of ASTM approved in Last previous edition approved as E8/ E8M.

Author: Mojas Tazilkree
Country: France
Language: English (Spanish)
Genre: Travel
Published (Last): 3 May 2011
Pages: 107
PDF File Size: 7.56 Mb
ePub File Size: 6.5 Mb
ISBN: 652-8-19358-930-2
Downloads: 77677
Price: Free* [*Free Regsitration Required]
Uploader: Bramuro

The gauge length is the most significant difference between E8 and E8M test specimens. For proper gripping, it is desirable that the entire length of the serrated face of each wedge be in contact with the specimen.

Brittle Materials—A schematic diagram of a gripping device for threaded-end specimens is shown in Fig. Both of these gripping devices should be attached to the heads of the testing machine through asym lubricated sphericalseated bearings. Originally approved in These wedge grips generally furnish e88 satisfactory means of gripping long specimens of ductile metal.

Any departure from this requirement may introduce bending stresses that are not included in the usual stress computation force divided by cross-sectional area. E8M Tensiont testing of metallic materials Juliano row Enviado por: For measuring elongation at fracture with an appropriate extensometer, the gauge length of the extensometer shall be equal to the nominal gauge length required for the specimen being tested.

ASTM E8 / E8M – 13 Standard Test Methods for Tension Testing of Metallic Materials

This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances. For short specimens and for specimens of many materials it is generally necessary to s8m machined test specimens and to use a special means of gripping to e8 that the specimens, when under load, shall be as nearly as possible in uniformly distributed pure axial tension see 5.


NOTE 3—Punching or blanking of the reduced section may produce significant cold work or shear burrs, or both, along the edges which should be removed by machining.

To ensure axial tensile stress e88m the gauge length, the axis of the test specimen should coincide with the center line of the heads of the testing machine. C39M – 16 – Compressive Strength of Cylindrical The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. For a standard This requires that liners of several thicknesses be available to cover the range of specimen thickness.

ASTM E8.E8M Tensiont testing of metallic materials –

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. NOTE 1—The effect of this eccentric force application may be illustrated by calculating the bending moment and stress thus added. It is important, therefore, that care be exercised in the preparation of specimens, particularly in the machining, to maximize precision and minimize bias in test results.

Astm c astm normas fibra de vidrio. Current edition approved May 1, A superscript epsilon indicates an editorial change since the last revision or reapproval.

A number in parentheses indicates the year of last reapproval. No further reproductions authorized. Proper alignment of wedge grips and liners is illustrated in Fig.


ASTM E8.E8M -15-Tensiont testing of metallic materials

8em liners are used behind the wedges, they must be of the same thickness and their faces must be flat and parallel.

The distance between spherical bearings should be as great as feasible. Parte 1 de 8 Designation: The test methods have been used extensively in the trade for this purpose.

This error increases to 2. Combining values from the two systems may result in non-conformance with the standard. For this reason, a small taper is permitted in the reduced section of each of the specimens described in the ast sections.

If, however, for any reason, one grip of a pair advances farther than the other as the grips tighten, an undesirable bending stress may be introduced. Astm a Astm a Such interpretation is usually applicable to values for reduction of area reported in the literature when no further qualification is given. The forces used in determining tensile strength and yield strength shall be within the verified force application range of the testing machine as defined in Practices E4.

Extensometers shall be used and verified to include the strains corresponding to the yield strength and elongation at fracture if determined. For best results, the wedges should be supported over their entire lengths by the heads of the testing machine.